TU516 1SAP212000R0001 ABB

DATA SHEET
TU515, TU516(-H), TU541, TU542
Terminal unit
1 Ordering data
Part no. Description Product life cycle phase *)
1SAP 212 200 R0001 TU515, I/O terminal unit, 24 V DC, screw
terminals
Active
1SAP 212 000 R0001 TU516, I/O terminal unit, 24 V DC, spring
terminals
Active
1SAP 412 000 R0001 TU516-XC, I/O terminal unit, 24 V DC,
spring terminals, XC version
Active
1SAP 215 000 R0001 TU516-H, I/O terminal unit, hot swap,
24 V DC, spring terminals, XC version
Active
1SAP 415 000 R0001 TU516-H-XC, I/O terminal unit, hot swap,
24 V DC, spring terminals
Active
1SAP 213 000 R0001 TU541, I/O terminal unit, 24 V DC, screw
terminals
Active
1SAP 213 200 R0001 TU542, I/O terminal unit, 24 V DC, spring
terminals
Active
1SAP 413 200 R0001 TU542-XC, I/O terminal unit, 24 V DC,
spring terminals, XC version
Active
1SAP 215 200 R0001 TU542-H, I/O terminal unit, hot swap,
24 V DC, spring terminals
Active
1SAP 415 200 R0001 TU542-H-XC, I/O terminal unit, hot swap,
24 V DC, spring terminals, XC version
Active
Ordering data
2023/08/05 3ADR010071, 9, en_US 1*) Modules in lifecycle Classic are available from stock but not recommended for
planning and commissioning of new installations.
2 Dimensions
1 Din rail 15 mm
2 Din rail 7.5 mm
The dimensions are in mm and in brackets in inch.
3 Technical data
The system data of AC500 and S500 are applicable to the standard version Ä Chapter 4 “System
data AC500” on page 3.
The system data of AC500-XC are applicable to the XC version Ä Chapter 5 “System data AC500-
XC” on page 8.
Only additional details are therefore documented below.
The technical data are also applicable to the XC version.
Parameter Value
Number of channels per module Max. 32
Distribution of the channels into groups 4 groups of 8 channels each (1.0 ... 1.7, 2.0 ...
2.7, 3.0 ... 3.7, 4.0 ... 4.7), the allocation of the
channels is given by the inserted I/O module
Rated voltage 24 V DC
Max. permitted total current 10 A, per separated process voltage terminal or
for internal connection of process voltages
Technical data
2 3ADR010071, 9, en_US 2023/08/05Parameter Value
Grounding Direct connection to the grounded DIN rail or via
the screws with wall mounting
Screw terminals Front terminal, conductor connection vertically
with respect to the printed circuit board
Spring terminals Front terminal, conductor connection vertically
with respect to the printed circuit board
Weight 200 g
Mounting position Horizontal or vertical
4 System data AC500
4.1 Environmental conditions
Table 1: Process and supply voltages
Parameter Value
24 V DC 
 Voltage 24 V (-15 %, +20 %)
Protection against reverse polarity Yes
120 V AC 
 Voltage 120 V (-15 %, +10 %)
Frequency 50/60 Hz (-6 %, +4 %)
230 V AC 
 Voltage 230 V AC (-15 %, +10 %)
Frequency 50/60 Hz (-6 %, +4 %)
120 V AC...240 V AC wide-range supply 
 Voltage 120 V ... 240 V (-15 %, +10 %)
Frequency 50/60 Hz (-6 %, +4 %)
Allowed interruptions of power supply, according to EN 61131-2
 DC supply Interruption < 10 ms, time between 2 interruptions
 > 1 s, PS2
AC supply Interruption < 0.5 periods, time between 2 interruptions
 > 1 s
NOTICE!
Risk of damaging the PLC due to improper voltage levels!
– Never exceed the maximum tolerance values for process and supply voltages.
– Never fall below the minimum tolerance values for process and supply voltages.
Observe the system data Ä Chapter 4 “System data AC500” on page 3 and the
technical data of the module used.